t_seriest

Technical Specifications

Dimensions

Head Dia.
1 inches (25.4 mm)
Body Dia.
0.85 inches (22 mm)
Length:
5 inches (126 mm)
Weight
2.3 ounces (66 grams)1

Battery Type

Operating voltage

  • 2.7V - 6V
  • Do not exceed 6V. Do not use two rechargeable CR123A.

What's included

  • P200LC2 flashlight
  • Spare o-rings
  • User Manual
  • Mil-Spec Para-cord Lanyard w/ quick attachment clip
  • CR123A Battery Magazines
  • Heavy duty nylon holsterwith flip
  • User removable tailcap lanyard ring

Carrying method

  • Para-cord lanyard with quick attachment clip
  • User removable stainless steel pocket clip (Titanium coated)

Waterproof

  • IPX-8 standard

Replaceable items

  • Lens

LED

  • CREE XM-L2 Cool White U4 LED
  • CREE XM-L2 Neutral White U2 LED
  • CREE XP-L HI V3 LED (Cool White)
  • CREE XP-L HI V2 LED (Neutral White)
  • Custom high power 395nm UV LED (5Watts)
  • Custom high power 365nm UV LED (5Watts)

Max output

  • CREE XM-L2 U4 LED
    • LED lumen: 1286
    • ANSI FL-14 lumen: 1053
  • CREE XM-L2 U2 LED
    • LED lumen: 1123
    • ANSI FL-14 lumen: 920
  • CREE XP-L HI V3:
    • LED lumen: 1095
    • ANSI FL-13 lumen: 950
  • 395nm UV LED:
    • Radiant power: 2000mW
  • 365nm UV LED:
    • Radiant power: 1400mW

Beam Profile

  • CREE XM-L2 U2 LED

    • Center lux: 10,100 lux
    • Center spot angle: 11.4°
    • Spill light angle: 51°
    • Beam distance: 220 yards / 201 meters


  • CREE XP-L HI V3 LED

    • Center lux: 15,200 lux
    • Beam distance: 269 yards / 247 meters

    Lens

    • Waterwhite glass lens w/ harden treatment
    • Anti-reflective (AR) coating on both side (96% transparency)

    LED circuit

    • C3000L TS
      • Ultra low dropout voltage (<0.2V) for longer current regulated runtime using single 18650 battery
      • High switching frequency (1MHz) controller for more compact circuitry design
      • Low internal resistance design offers up to 99% efficiency7
      • Non-dimming constant current regulation for all output levels
      • Zero standby current
      • Energy saving feature5

    Reflector

    • Smooth aluminum reflector

    Material

    • HAIII hard anodization aerospace aluminum

    Output and Runtime

    • Three brightness levels
      • CREE XM-L2 U4 LED
        • Led lumen: 12865-1145/366/40
        • ANSI FL-1 lumen: 10535-918/292/32
      • CREE XP-L HI V3 LED
        • Led lumen: 10955-1030/314/33
        • ANSI FL-1 lumen: 9505-885/265/26
      • Runtime:
      • 1.5/6/80 hours (1x18650)
        0.8/3.5/40 hours (2xCR123A)

    Operations

    • Tactical forward clicky switch
      • Turn on the light by pressing the tailcap button until it clicks.
      • Twist the head to select between three output levels.
      • You can pre-selected output level before turning on the light.

    Controls

    Other features

    • User replaceable glass lens
    • Battery reverse polarity protection
    • Ultra low internal resistance phosphor bronze springs (silver coated)
    • Spring loaded positive and negative terminal

    Warranty

    Battery Safety Precaution

    Ensure the protective circuit on the 18650 batteries has current limitation of higher than 5A. Always use proven EAGTAC batteries for best performance and reliability.

    All EAGTAC flashlights are designed to use button-top battery (battery with protruding positive terminal). For rechargeable li-ion battery, use only EAGTAC li-ion battery, or other protected li-ion battery with compatible length and diameter. Before using the battery, check and ensure the battery outer wrapping (the isolating plastic film that wraps around the metal housing of the battery) is complete. Broken battery wrapping may lead to short circuit and damage to the flashlight.

    Lithium and Li-ion battery can explode or cause burns if disassembled, shorted, or exposed to high temperature. Do not mix new and used batteries. Do not mix batteries with different brand, capacity, voltage, or install batteries backwards.

    NiMH rechargeable battery may release gas during discharge. If you experience an inflated switch boot or find high pressure being built inside the flashlight, switch off the flashlight immediately. Slowly loosen the tail-cap to reduce the internal pressure and replace all batteries.     Back to top

    Flashlight Maintenance

    Periodically clean the threads and o-rings with a lint free cloth and apply a thin coating of EAGTAC synthetic grease to the o-rings and threads. After prolonged exposure to moisture, the head and batteries should be removed, inspected, and dried. Do not touch or attempt to clean the reflector, as it will scratch the reflective coating permanently.     Back to top

    1. This weight measurement does not include batteries
    2. All batteries must have protruding top button.
    3. Beam output diameter taken at one meter
    4. ANSI FL-1 Lumens is a measurement of light output standardized by American National Standards Institute for use with flashlights. This ANSI Lumen measurement is the total overall light output being emitted from the flashlight. This measurement is generally more accurate as it takes into consideration the loss from reflector/lens/bezel. EAGTAC’s ANSI Lumen output is measured using a calibrated integrated sphere three minutes after turning on the flashlight. For O.T.F. lumen, measurement is taken one minute after turning on the flashlight.
    5. Energy saving feature reduce the maximum output current from 100% to 85% after 200 seconds at turbo output.
    6. Runtime is measured with energy saving feature enabled using three EAGTAC 3400mAh batteries.
    7. Maximum efficiency occurs when input voltage is very close to LED forward voltage.